The following define the most widely used symbols and equations for capacitance (in series, parallel, quantity of stored electricity etc.), Ohm's Law (for DC circuits) and the decibel. We would also suggest you look at this 6 volume series of books by Tony R Kuphaldt 'Lessons in Electric Circuits' published under the OpenBook initiative (means its free).
Symbol | Meaning |
C | Capacitance measured in Farads (F): Degrees Celsius (temperature) |
D | Dissipation factor; reciprocal of storage factor Q. |
d | Thickness of dielectric material in a capacitor (measured in centimeters) |
dB | Decibel; the ratio between two amounts of Power |
E | Electromotive Force measured in Volts |
F | Farads (measure of Capacitance); Degrees Farenheit (temperature) |
f | Frequency measured in Hertz. |
G | Conductance measured in siemens or mhos. |
I | Current measured in amperes. |
J | Energy, work or quantity of heat measured in Joules. |
L | Inductance measured in henries. |
M | Mutual inductance measured in henries. |
P | Power measured in Watts. |
Q | Quality or an inductor or Quantity of electricity stored (measured in coulombs). |
R | Resistance measured in Ohms. |
Z | Impedance measured in ohms. |
In Parallel
C_{total} = C_{1} + C_{2} etc.
In Series
C_{total} = 1 / (1 / C_{1} + 1 / C_{2} etc.)
OR
1/ C_{total} = 1 / C_{1} + 1 / C_{2} etc.
Two Capacitors in series
C_{total} = C_{1} * C_{2} / C_{1} + C_{2}
Capacitance of a Capacitor
C = 0.0885 KS (N - 1) / d
Quantity of Electricity Stored in a capacitor
Q = CE
The following equations are valid for DC circuits only. Where E = volts, P = watts (power), I = current, R = resistance.
I = E / R (current = volts / resistance)
I = [SR] P / R (current = square root of power / resistance)
I = P / E (current = power / volts)
R = E / I (resistance = volts / current)
R = P / I^{2} (resistance = power / current squared)
R = E^{2} / P (resistance = volts squared / power)
E = IR (volts = current * resistance)
E = P / I (volts = power / current)
E = [SR] PR (volts = square root power * resistance)
P = I^{2}R (power = current squared * resistance)
P = EI (power = volts * current)
P = E^{2} / R (power = volts squared / resistance)
The Decibel - a relative measure of two values is calculated for electrical circuits as:
Problems, comments, suggestions, corrections (including broken links) or something to add? Please take the time from a busy life to 'mail us' (at top of screen), the webmaster (below) or info-support at zytrax. You will have a warm inner glow for the rest of the day.
Tech Stuff
If you are happy it's OK - but your browser is giving a less than optimal experience on our site. You could, at no charge, upgrade to a W3C standards compliant browser such as Firefox
Search
Share
Page
Standards
ISO (International)
IEC (International)
ANSI (US)
DIN (Germany)
ETSI (EU)
BSI (UK)
AFNOR (France)
Telecom
TIA (US)
ECIA (US)
ITU (International)
IEEE (US)
ETSI (EU)
OFCOM (UK)
Internet
Electronics
Site
Copyright © 1994 - 2018 ZyTrax, Inc. All rights reserved. Legal and Privacy |
site by zytrax |
web-master at zytrax Page modified: October 21 2015. |